BotRescueBotRescue

Error Codes

Find what your robot error means and how to fix it — then DIY or request mail-in repair.

Error 42Dock Maintenance Brush Jammed

If the Roborock Error 42 brush stopped on the left, clear debris jamming the brush path. If it stopped on the right, clean or reseat the cleaning-sink water filter until it clicks. Wipe grit from the cleaning tank and retry mop washing. If Error 42 returns with a clear brush path and locked filter, request dock brush-module repair.

Error 13Charging Error

Clean charging contacts on the dock and robot with a soft cloth moistened with alcohol or a soft eraser; dry fully. Confirm the dock indicator is solid on when empty and off when docked (per your dock style). Seat the power cable firmly, try another outlet, then unplug the dock for 2 minutes and retry. If Error 13 persists, request battery or dock repair.

Cleaning Sink FullCleaning sink full or will not drain

If the station indicator is flashing, unplug the station, reconnect it, then continue. Remove the dirty-water tank, clean and refit the sealing plugs, clean the lid sealing ring, and close the lid firmly. Reseat the tank, press it down, and use Exit or Return in the app to test whether dirty water recycles. If it still will not drain, take the robot off the station and clear debris from the cleaning-sink suction nozzle. If the sink is empty but still reports full, wipe the water-level sensors on both sides of the sink with a tissue. If it still fails with clean seals and a clear nozzle, the station pump or sensor needs repair.

Water Leak / Level SensorCleaning-sink water-level sensors false full or leak-style alert

If the station indicator is flashing, unplug it, wait, and plug it back in before other checks. Take the robot off the station. If the sink is empty but still alerts, wipe the water-level sensors on both sides of the sink with a tissue. Clear debris from the sink suction nozzle. Remove the dirty-water tank, reseat the sealing plugs, close the lid firmly, and press the tank down. Confirm the float in the mop-washing tray moves freely and its magnet is still fitted. If the empty sink still alerts after clean sensors, the station sensor or pump needs repair.

Mopping Pad PlatesMopping Pad Plate Not Properly Installed

Power off and flip the robot. Remove mop cloths, clear hair/string from the plates and mounts, wipe plate connectors dry, then press both plates in until you hear a click. Restart the robot. If the mopping pad plate is still not properly installed after a clean click-fit, request plate-drive repair.

Error 2 (beeps 2)Clear the Brushes (Main Brush Stall)

Remove the brushes and clear hair from the rollers and end caps. Test briefly with brushes removed if your series allows it — if Error 2 clears, the brushes or ends were binding. Reinstall clean brushes and run on hard floor. Reboot by holding power ~10 seconds off-dock, then 3 seconds on. If Error 2 persists after cleaning and reboot, replace the brushes or request drive repair.

Auto-Empty FailedBase station will not empty the dustbin

Close the dust-tank cover and check the dust bag is fitted; replace it if full. Clear debris from the dust-collection ports on the robot, station, and dust box. In the Dreame app, enable Dust Collection and turn off or adjust Do Not Disturb. Wipe the window near the charging electrodes with a dry tissue. If emptying still fails with a new bag and clear ports, the station blower or air path needs repair.

Auto-Empty Not WorkingDock will not empty the dustbin

In the Roborock app, enable Auto-Emptying and check Do Not Disturb is not blocking it. Confirm the dock dust container cover and dust bag are fitted; replace a full bag and unfold it fully. Charge above 10% and run Empty manually — auto-empty will not trigger after a hand-placed dock or a return without cleaning. Reseat the main brush and brush cover. Clear fluff from the robot dust outlet, filter, air duct, suction inlet, and the dock air inlet. If it still fails with a clear path and a new bag, the dock blower or air path needs repair.

Cannot Return to DockRobot cannot find, return to, or complete docking

Confirm the station is powered and was not moved, and clear obstacles around it. Place it against a wall with about 5 cm clear each side and 1.5 m clear in front, away from mirrors and windows opposite. Wipe the station signal area, charging-contact window, and charging pins with a dry cloth. Put the robot 1–2 m in front and press Return; start cleans from the dock so the map stays linked. Check the drive wheels are free and not slipping on a wet floor. If docking still fails, the dock beacon or robot sensor needs repair.

Cutting System BlockedBlade Disc Stopped

Switch the Automower off and remove the safety key / set to STOP. Check under the cutting deck, around the blade disc, wheels, and between body and chassis for wrapped grass or objects; clear safely. Free the mower if it is caught on a root or trampoline leg and add a stay-out zone if that spot repeats. Lower cutting height only within the model’s max grass-height guidance. If the disc still will not turn freely after cleaning, request cutting-system service.

Error 1LiDAR Turret or Laser Blocked

Power on and watch the laser unit — it should spin smoothly. If it does not spin, gently rotate it by hand about one full turn to free hair or grit, then restart. Wipe dust around the tower with a soft dry cloth; do not force the housing open or spray liquids into the turret. If Error 1 returns with a free-spinning tower, request LDS module repair.

Error 10Filter Wet or Blocked

Remove the washable filter. Tap out dirt and rinse if needed, then dry thoroughly for at least 24 hours (use a spare filter meanwhile). Reinstall a completely dry filter and empty dustbin. Restart cleaning. If Error 10 continues with a dry clean filter, replace the filter; recurring faults may need fan/air-path service.

Error 11High-Intensity Magnetic Field

Move the robot away from magnetic tape, metal thresholds, or the dock’s strong magnet zone. Place it on open floor and restart. If Error 11 fires away from any magnets, request sensor diagnosis — do not assume a Wi-Fi fault.

Error 12Battery Too Low

Dock the robot and confirm charging starts (dock indicator behaviour per your manual). Leave it until charged enough for a full job. If Error 12 appears right after a full charge, clean charging contacts and see Error 13 steps; persistent no-charge needs battery or dock repair.

Error 14 / 1-4Bin Not Detected

Confirm the bin is fully installed and latched. Wipe bin contacts on both the bin and the robot with a clean, lightly dampened melamine foam (for example a Magic Eraser), then dry. Press CLEAN to restart. If Error 14 / 1-4 persists, the bin may need replacement — contact iRobot or request BotRescue diagnosis.

Error 2Bumper Stuck

Power off. Clean around the bumper and lightly tap it to free any catch. Check for cables, fringe, or furniture trapping the bumper. Move the robot to open floor and restart cleaning. If Error 2 returns with a free bumper, request bumper-sensor repair.

Error 3Wheels Suspended

Pick the robot up and place it on flat open floor so both drive wheels sit firmly. Clear thresholds or furniture that left a wheel hanging. Restart cleaning. If Error 3 repeats on flat ground, request wheel-module inspection.

Error 4Cliff Sensor Error

Wipe the cliff-sensor windows on the underside with a soft dry cloth. Move the robot away from stairs, dark thresholds, or reflective edges. Restart cleaning. If Error 4 continues on open floor after cleaning, request cliff-sensor repair.

Error 5Main Brush Jammed

Flip the robot, remove the main-brush cover, and take out the brush. Clear hair from the brush, both ends, bearings, and the two installation slots. Reinstall until the cover locks. Run a short clean with Carpet mode enabled. If Error 5 returns after a thorough clean, request main-brush motor or gearbox repair.

Error 6Side Brush Jammed

Remove the side brush (usually one screw). Clear hair and string from the brush and the shaft. Reinstall firmly. Restart cleaning. If Error 6 returns with a clean free-spinning brush, request side-brush motor repair.

Error 7Wheels Jammed

Flip the robot and clear hair or debris from both drive wheels and axles. Spin each wheel by hand. Move the robot to open floor and restart. If a wheel still binds after cleaning, request wheel-module repair.

Error 8Robot Trapped

Lift the robot clear of the obstacle zone. Tidy cables and raise low furniture clearance if it often traps there. Restart from open floor. If Error 8 fires repeatedly in open space, run diagnosis — navigation or bumper sensors may need service.

Error 9No Dustbin / Filter Not Detected

Reseat the dustbin until it latches. Remove the washable filter and confirm the side magnet is present; if missing, replace the filter. Reinstall filter and bin firmly, then restart. If Error 9 persists with a known-good filter and latched bin, request dustbin-detect repair.

GFCI TripGround Fault — Cable or Supply

Reset the GFCI and confirm the outlet works with another device. Unplug any extension cord or surge strip; plug the power supply directly into a working GFCI outlet. Inspect the blue floating cable and black mains cord for cuts, kinks, or frays — replace a damaged cable. Disconnect the blue cable and power the supply alone: if it stays on, the fault is in the cable or robot (dealer / BotRescue); if it still trips or will not power, the supply likely needs replacement.

No Loop SignalBoundary Wire Signal Lost

At the charging station, reseat boundary and guide wire ends until contacts are clean and fully inserted. Inspect splices and look for cuts from gardening or weather. If the lamp still flashes blue, bisect the loop to find the break and repair with a waterproof coupler. If the lamp is green but the mower still reports no loop, check ECO mode, max distance from the wire, and interference — then create a new loop signal in settings or contact a dealer / BotRescue for installation help.

Unable to DockRobot cannot find or climb onto the dock

Place the dock against a wall with about 0.5 m clear on each side and 1.5 m clear in front. Wipe the dock's front signal area and the robot's front and recharge sensors. If the dock was moved, place the robot nearby and tap Return to dock so the map position updates. Clear rugs, cables, and chairs from the approach. If docking still fails with clean sensors and clear space, the dock beacon or robot sensor needs repair.

Washboard Water AbnormalAbnormal washboard water level or dirty tank will not pump

Remove the washboard, clear sludge from the sewage outlet underneath, and wipe the metal overflow sensors dry. Clean the sewage filter and any connected drain pipe. Empty the dirty-water tank, clean the sealing rings and lid so it is airtight, and fasten the clip. Press the tank firmly down so the seal seats. Remove the cleaning tray, empty it, rinse the tray filter, dry the base, and refit tray and washboard. If pumping still fails with clean seals and a clear outlet, the station pump needs repair.